How to replace the front brake calipers on Chevrolet Impala?

A technician should start the front brake caliper replacement process by checking the brake master cylinder reservoir fluid position. Check fluid levels in the master cylinder reservoir until they sit at the average position between maximum and minimum limits. First support the vehicle then lift it before removing both front tire assemblies. Apply enough pressure with a large c-clamp on top of the brake caliper that pushes the piston into the caliper bore to free the caliper from the rotor. Remove the c-clamp followed by removal of the brake hose-to-caliper bolt which requires discarding the 2 copper brake hose gaskets . Secure the opening of the front brake hose with a plug to avoid substantial fluid loss. The leading caliper pin bolt uses a bushing but the trailing pin bolt remains solid without a bushing. You must disassemble the caliper pin bolts and remove the caliper from the rotor and caliper bracket connection. Examine the caliper bolt boots for damage before replacing defective parts and inspect the caliper bolts for both corrosion and damage using new caliper pin bolts if needed. Application of gm p/n 18047666 lubricant or its equivalent must be performed on brake caliper pin bolts and bushing after removing all debris, old lubricant and ensuring that lubricant distribution is uniform without creating excess buildup on the leading caliper pin end. Position the caliper over the rotor so that it joins the caliper bracket while directing the leading caliper pin bolt through its bushing and maintaining a solid trailing pin bolt. Securely position caliper pin bolts before fitting bolt boots into their respective grooves. Replace any damaged pin bolt boots and tighten the bolts to 95 nm (70 ft. Lbs.). Mount the brake hose bolt to the brake hose using new copper brake hose gaskets . Tighten the brake hose-to-caliper bolt to 54 nm (40 ft. Lbs.). Start by removing the 2 wheel lug nuts and placing the front tire with its matching wheel assembly on the vehicle then lower it to the ground. Next fill the master cylinder with clean brake fluid to the specified level while bleeding the brakes then examine for fluid leaks.

How to service and repair the front brake calipers on Chevrolet Impala?

The first step to service or repair the front brake caliper requires caliper removal. Avoid sticking your fingers in front of the caliper Piston(s) when using compressed air because the Piston(s) could forcefully discharge and potentially cause injuries to your hands. When removing pistons from caliper housing use clean cloths for padding along with sufficient air application to let the pistons leave their bores without causing any harm. Blow compressed air into the caliper inlet hole to push out the Piston through its Piston boot. The inspection of the Piston should evaluate its condition for scoring as well as nicks and corrosion and worn chrome plating because any irregularities require replacement. Use a small wooden or plastic tool to remove the Piston seal safely from the caliper bore's groove after you remove the caliper boot carefully without damaging the housing bore. Check the caliper bore and seal grooves for any signs of scoring or nicks or corrosion and wear because light corrosion should be polished with a crocus cloth. Consider replacing the caliper housing when corrosion prevention measures fail to work on the seal groove. Inspect bolt boots for any signs of damage including cuts and tears and replace any defective boots. Check caliper bolts for damage and corrosion then discard corroded bolts unless new replacement bolts are available. Replace the caliper when its bore contains any damage to the seal groove since this condition will lead to braking issues. Before assembly, clean all caliper housing and bleeder valve components in denatured alcohol and blow out their passages with filtered non-lubricated compressed air. Use the j 36349 front dust boot seal installer to place the bleeder valve cap and bleeder valve into position on the caliper housing and tighten the bleeder valve to 13 nm (115 inch lbs.). Set the new lubricated Piston seal properly into the caliper bore grooves before putting the lubricated boot on the Piston. Then, apply brake fluid to lubricate the Piston's outside diameter. Apply the j 36349 front dust boot seal installer to push the Piston down in the caliper bore before seating the caliper boot inside the counterbored caliper housing. Finally, install the caliper.

OEM Chevrolet Impala Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Brake Calipers found

View related parts
Chevrolet Impala Caliper, Rear Driver Side Part Number: 25990068
$183.22 MSRP: $353.95
You Save: $170.73 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Driver Side
- Replaces: 18048683, 88965581
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX
View related parts
Chevrolet Impala Caliper Assembly, Driver Side Part Number: 13279638
$145.82 MSRP: $281.39
You Save: $135.57 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Caliper Assembly, Passenger Side Part Number: 13279639
$145.82 MSRP: $281.39
You Save: $135.57 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper; Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Caliper, Rear Passenger Side Part Number: 25990067
$146.64 MSRP: $285.46
You Save: $138.82 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Replaces: 18048684, 88965582
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX
View related parts
Chevrolet Impala Caliper, Front Part Number: 19141350
$54.14 MSRP: $98.79
You Save: $44.65 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper
- Position: Front
- Replaces: 18021163, 18039664
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Caliper, Front Part Number: 19141351
$54.14 MSRP: $98.79
You Save: $44.65 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper
- Position: Front
- Replaces: 18021162, 18037480, 18039665
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Caliper, Front Passenger Side Part Number: 25983763
$120.22 MSRP: $217.61
You Save: $97.39 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 21993095
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Impala | Police | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Impala Caliper, Silver, Rear Driver Side Part Number: 13533556
$97.37 MSRP: $200.55
You Save: $103.18 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing-Rear Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear Driver Side
- Replaces: 13579138, 13275899
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Caliper, Front Driver Side Part Number: 18046196
$145.18 MSRP: $284.26
You Save: $139.08 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18029818
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Caliper, Silver, Rear Passenger Side Part Number: 13533555
$89.07 MSRP: $244.85
You Save: $155.78 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing-Rear Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper; Housing, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear Passenger Side
- Replaces: 13275900, 13579139
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Caliper, Front Passenger Side Part Number: 18046197
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18029819
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Caliper Overhaul Kit, Rear Part Number: 18023387
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper Piston; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Caliper Part Number: 18021518
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Caliper, Passenger Side Part Number: 18015428
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996, 1984-1985 Chevrolet Impala | Base, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Caliper, Front Passenger Side Part Number: 25983765
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 15251789
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Caliper Piston Part Number: 88967227
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Brake Caliper Piston; Caliper Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2011 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Caliper, Front Driver Side Part Number: 25983764
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 15251788
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Caliper Overhaul Kit, Rear Part Number: 18021522
Product Specifications
- Other Name: Repair Kit, Rear Brake Caliper; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Caliper, Driver Side Part Number: 25983762
$121.31 MSRP: $217.61
You Save: $96.30 (45%)
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Replaces: 21993094
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Impala | Police | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Impala Overhaul Kit, Front Part Number: 18017156
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Wheel Brake Cylinder/Caliper Piston Kit.
- Position: Front
- Replaces: 18024958
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS

| Page 1 of 2 |Next >

1-20 of 24 Results

Chevrolet Impala Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Impala parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Impala Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Brake Caliperss on Chevrolet Impala is part of disc brake system that produce the required force to slow or stop the car. When the brake pedal is pushed, a brake fluid extends the caliper's pistons with pressure, this then forces the brake pad to come into contact with the rotor. This action put into place totally ceases the rotation of the wheel. Chevrolet Impala models utilize two primary types of brake calipers: terminological: fixed and floating. As with the floating calipers, the fixed ones are firmly situated and the pistons are located on both sides of the rotor but cost a lot more. The other type of brake caliper is the floating calipers which are also referred to as sliding calipers, they have a single piston that slides the caliper so as to apply pressure on both faces of the rotor. Floating calipers are easier to manufacture and cheaper than fixed versions; however, they tend to develop glitches such as sticking and that contribute to wear and tear, thus reducing efficiency. The brake caliper has to be designed and constructed in the right manner in order for it to improve the safety and performance of the Impala.

Chevrolet Impala Brake Calipers Parts and Q&A

Caliper, Front Driver Side
18046196
Q: How to replace the front brake calipers on Chevrolet Impala?
A:
A technician should start the front brake caliper replacement process by checking the brake master cylinder reservoir fluid position. Check fluid levels in the master cylinder reservoir until they sit at the average position between maximum and minimum limits. First support the vehicle then lift it before removing both front tire assemblies. Apply enough pressure with a large c-clamp on top of the brake caliper that pushes the piston into the caliper bore to free the caliper from the rotor. Remove the c-clamp followed by removal of the brake hose-to-caliper bolt which requires discarding the 2 copper brake hose gaskets . Secure the opening of the front brake hose with a plug to avoid substantial fluid loss. The leading caliper pin bolt uses a bushing but the trailing pin bolt remains solid without a bushing. You must disassemble the caliper pin bolts and remove the caliper from the rotor and caliper bracket connection. Examine the caliper bolt boots for damage before replacing defective parts and inspect the caliper bolts for both corrosion and damage using new caliper pin bolts if needed. Application of gm p/n 18047666 lubricant or its equivalent must be performed on brake caliper pin bolts and bushing after removing all debris, old lubricant and ensuring that lubricant distribution is uniform without creating excess buildup on the leading caliper pin end. Position the caliper over the rotor so that it joins the caliper bracket while directing the leading caliper pin bolt through its bushing and maintaining a solid trailing pin bolt. Securely position caliper pin bolts before fitting bolt boots into their respective grooves. Replace any damaged pin bolt boots and tighten the bolts to 95 nm (70 ft. Lbs.). Mount the brake hose bolt to the brake hose using new copper brake hose gaskets . Tighten the brake hose-to-caliper bolt to 54 nm (40 ft. Lbs.). Start by removing the 2 wheel lug nuts and placing the front tire with its matching wheel assembly on the vehicle then lower it to the ground. Next fill the master cylinder with clean brake fluid to the specified level while bleeding the brakes then examine for fluid leaks.
Caliper, Front Passenger Side
18046197
Q: How to service and repair the front brake calipers on Chevrolet Impala?
A:
The first step to service or repair the front brake caliper requires caliper removal. Avoid sticking your fingers in front of the caliper Piston(s) when using compressed air because the Piston(s) could forcefully discharge and potentially cause injuries to your hands. When removing pistons from caliper housing use clean cloths for padding along with sufficient air application to let the pistons leave their bores without causing any harm. Blow compressed air into the caliper inlet hole to push out the Piston through its Piston boot. The inspection of the Piston should evaluate its condition for scoring as well as nicks and corrosion and worn chrome plating because any irregularities require replacement. Use a small wooden or plastic tool to remove the Piston seal safely from the caliper bore's groove after you remove the caliper boot carefully without damaging the housing bore. Check the caliper bore and seal grooves for any signs of scoring or nicks or corrosion and wear because light corrosion should be polished with a crocus cloth. Consider replacing the caliper housing when corrosion prevention measures fail to work on the seal groove. Inspect bolt boots for any signs of damage including cuts and tears and replace any defective boots. Check caliper bolts for damage and corrosion then discard corroded bolts unless new replacement bolts are available. Replace the caliper when its bore contains any damage to the seal groove since this condition will lead to braking issues. Before assembly, clean all caliper housing and bleeder valve components in denatured alcohol and blow out their passages with filtered non-lubricated compressed air. Use the j 36349 front dust boot seal installer to place the bleeder valve cap and bleeder valve into position on the caliper housing and tighten the bleeder valve to 13 nm (115 inch lbs.). Set the new lubricated Piston seal properly into the caliper bore grooves before putting the lubricated boot on the Piston. Then, apply brake fluid to lubricate the Piston's outside diameter. Apply the j 36349 front dust boot seal installer to push the Piston down in the caliper bore before seating the caliper boot inside the counterbored caliper housing. Finally, install the caliper.