How to replace the Power Steering Hose Inlet on Chevrolet Uplander?

The first step to replace the power steering gear inlet pipe/hose requires the steering wheel set straight forward and secured before key removal. Start the procedure by removing three main elements: manifold cover followed by the Drive Belt and washer solvent container. Start by removing the bolt from the Drive Belt idler pulley before you take out both pulley and the three bolts from the engine lift bracket. Begin by removing the power steering pulley and Power Steering Pump along with its inlet pipe/hoses routing clip nut at the generator before separating the power steering gear inlet pipe/hose from this clip. Place a drain pan under the power steering implements before you remove both the Power Steering Pump and gear inlet pipe/hose fitting from the pump whilst discarding the standard o-ring seal. Stack the vehicle to a suitable height while disconnecting the intermediate shaft from the rack and pinion stub shaft for protection purposes. Detach the intermediate shaft pinch bolt followed by separating the intermediate shaft from the steering gear while lowering the rear of the cradle support after removing its two rear bolts. First disconnect and discard the power steering gear inlet pipe/hose fitting which is attached to the steering gear by removing the heat shield bolts and shield. The technician needs to take out the power steering gear inlet pipe/hose from inside the vehicle. The new power steering gear inlet pipe/hose requires installation by connecting it to the steering gear with a new o-ring seal while tightening the fitting to 27 n.m (20 lb ft). Tighten the bolts of the steering gear heat shield to 124 pounds of an inch. The installation of the two rear cradle support bolts must be accomplished at 165n.m torque or 122 lb ft measurements. After steering gear bolt tightening reaches 48 n.m (35 lb ft) position, lower the vehicle. Secure the power steering gear inlet pipe/hose fitting to the steering gear through an installation of a new o-ring seal followed by tight torque setting to 27 n.m (20 lb ft). Install the power steering gear inlet pipe/hose to its routing clip while torquing the nut to 10 n.m (89 lb in). Set the Power Steering Pump pulley along with engine lift bracket using three bolts at 50 n.m (37 lb ft) torque and install the Drive Belt idler pulley through its bolt torqued at 50 n.m (37 lb ft). The last step involves returning the washer solvent container together with the Drive Belt and intake manifold cover while filling and bleeding the power steering system.

OEM Chevrolet Uplander Power Steering Hose

Power Steering Pressure Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Power Steering Hoses found

View related parts
Chevrolet Uplander Power Steering Cooler Part Number: 15283101
$81.69 MSRP: $129.70
You Save: $48.01 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Power Steering Fluid Cooling; Power Steering Hose; Power Steering Return Hose; Cooling Pipe; Hose, Steering Fluid Cooler
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS
View related parts
Chevrolet Uplander Pipe Kit Part Number: 88963469
$15.20 MSRP: $30.53
You Save: $15.33 (51%)
ADD TO CART
Product Specifications
- Other Name: Pipe Kit, Steering Gear Left; Power Steering Hose; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Cooler Part Number: 15777213
$100.57 MSRP: $159.65
You Save: $59.08 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Power Steering Fluid Cooling; Power Steering Hose; Power Steering Return Hose; Cooling Pipe; Hose, Steering Fluid Cooler
- Replaced by: 19540437
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Return Hose Part Number: 15233978
Product Specifications
- Other Name: Hose; Power Steering Hose
- Replaced by: 15777212
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Pipe Kit Part Number: 88963470
Product Specifications
- Other Name: Pipe Kit, Hydraulic Steering Gear Pressure; Power Steering Hose; Pipe Kit, Steering Gear Oil Pressure
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Pipe Kit, Passenger Side Part Number: 26081831
Product Specifications
- Other Name: Pipe Kit, Steering Gear; Power Steering Hose; Pressure Line; Line Kit; Line; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Pipe Kit, Driver Side Part Number: 26081830
Product Specifications
- Other Name: Pipe Kit, Steering Gear; Power Steering Hose; Pressure Line; Line Kit; Line; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Pressure Hose Part Number: 19333426
Product Specifications
- Other Name: Hose, Steering Gear Oil Pressure; Power Steering Hose; Pressure Hose; Hose, Hydraulic Steering Gear Pressure
- Replaces: 15777210
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Return Hose Part Number: 15893685
Product Specifications
- Other Name: Pipe, Steering Gear Oil Return; Power Steering Hose; Inlet Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Pressure Hose Part Number: 15777622
Product Specifications
- Other Name: Hose Assembly-Power Steering Gear Inlet; Power Steering Hose; Pressure Hose; Hose, Hydraulic Steering Gear Pressure; Hose, Steering Gear Oil Pressure
- Replaces: 10311306
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Cooler Part Number: 15777212
Product Specifications
- Other Name: Hose Assembly-Power Steering Fluid Cooling; Power Steering Hose; Power Steering Return Hose; Cooling Pipe; Hose, Steering Fluid Cooler
- Replaces: 15233978, 15197545
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Pressure Hose Part Number: 15777209
Product Specifications
- Other Name: Hose Assembly-Power Steering Gear Inlet; Power Steering Hose; Pressure Hose; Hose, Hydraulic Steering Gear Pressure; Hose, Steering Gear Oil Pressure
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Power Steering Return Hose Part Number: 15777207
Product Specifications
- Other Name: Pipe, Steering Gear Oil Return; Power Steering Hose; Inlet Pipe
- Replaces: 15293050
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS
View related parts
Chevrolet Uplander Power Steering Return Hose Part Number: 15293049
Product Specifications
- Other Name: Pipe, Steering Gear Oil Return; Power Steering Hose; Inlet Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS

Chevrolet Uplander Power Steering Hose

Want to cut long-term maintenance and repair costs? Choose OEM Power Steering Hose. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Uplander parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Uplander Power Steering Hose includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Uplander Power Steering Hose is a part that serves to improve the quality of the Chevrolet Uplander, a model of minivan made by Chevrolet for 2005-2009 years. This Power Steering Hose helps in transferring the hydraulic fluid from the power steering pump to the steering gear so as to enable the steering control and enhance the vehicle's maneuverability. The Chevrolet Uplander Power Steering Hose is a high pressure part as well, the hose that is used is made in such a way that it is strong and prolongs the life of the hose by withstanding pressure, heat, and the environment hence increasing the steering capacity. Making the Power Steering Hose compatible with different Uplander models guarantees that the driver will get the suitable hose based on his or her vehicles configurations, if the vehicle uses rubber hoses or curved metal tubing. Therefore, essential reasoning exists that goes beyond fundamental component application; the Chevrolet Uplander Power Steering Hose serves to improve not just power steering system performance efficiency but offers safety as well by avoiding potential leakage that can result in above-stated issues. Also, the proper installation of Power Steering Hose and its appropriate routing with causing any sort of damage is very important for the optimum performance of the car for the longest time. The Chevrolet Uplander Power Steering Hose is one of the most durable parts in the auto market and plays a paramount significance in the steering system, so both attractive advantages make buyers of this car excited to use original parts for maintaining and enhancing their automobiles' performance. In general, Chevrolet Uplander Power Steering Hose is one of the most important components of the car and in general contribute to Uplander model smooth and safety driving.

Chevrolet Uplander Power Steering Hose Parts and Q&A

Power Steering Cooler
15777213
Q: How to replace the Power Steering Hose Inlet on Chevrolet Uplander?
A:
The first step to replace the power steering gear inlet pipe/hose requires the steering wheel set straight forward and secured before key removal. Start the procedure by removing three main elements: manifold cover followed by the Drive Belt and washer solvent container. Start by removing the bolt from the Drive Belt idler pulley before you take out both pulley and the three bolts from the engine lift bracket. Begin by removing the power steering pulley and Power Steering Pump along with its inlet pipe/hoses routing clip nut at the generator before separating the power steering gear inlet pipe/hose from this clip. Place a drain pan under the power steering implements before you remove both the Power Steering Pump and gear inlet pipe/hose fitting from the pump whilst discarding the standard o-ring seal. Stack the vehicle to a suitable height while disconnecting the intermediate shaft from the rack and pinion stub shaft for protection purposes. Detach the intermediate shaft pinch bolt followed by separating the intermediate shaft from the steering gear while lowering the rear of the cradle support after removing its two rear bolts. First disconnect and discard the power steering gear inlet pipe/hose fitting which is attached to the steering gear by removing the heat shield bolts and shield. The technician needs to take out the power steering gear inlet pipe/hose from inside the vehicle. The new power steering gear inlet pipe/hose requires installation by connecting it to the steering gear with a new o-ring seal while tightening the fitting to 27 n.m (20 lb ft). Tighten the bolts of the steering gear heat shield to 124 pounds of an inch. The installation of the two rear cradle support bolts must be accomplished at 165n.m torque or 122 lb ft measurements. After steering gear bolt tightening reaches 48 n.m (35 lb ft) position, lower the vehicle. Secure the power steering gear inlet pipe/hose fitting to the steering gear through an installation of a new o-ring seal followed by tight torque setting to 27 n.m (20 lb ft). Install the power steering gear inlet pipe/hose to its routing clip while torquing the nut to 10 n.m (89 lb in). Set the Power Steering Pump pulley along with engine lift bracket using three bolts at 50 n.m (37 lb ft) torque and install the Drive Belt idler pulley through its bolt torqued at 50 n.m (37 lb ft). The last step involves returning the washer solvent container together with the Drive Belt and intake manifold cover while filling and bleeding the power steering system.